How to Make a Unicorn Horn Flower Crown



Due to the fact that who should need to decide between a flower crown and a unicorn horn? Kaia really wished to use both for her Birthday, and this is what I ended up with.

When she initially informed me she wished to be a unicorn for her Birthday party, I started poking around the Web, attempting to figure something out. I was actually dissatisfied with what I found. I didn't desire her to be overloaded by a big, hot, bulky outfit for her indoor celebration. I wanted something she could wear on her own when she desired to play. I didn't want a modeling clay horn held on with an "undetectable" flexible band. These just don't appear useful to me for a young kid. I wanted a horn that would go on quickly and conveniently, one that was lightweight, was not fragile, and would remain in location well on her head while she cantered around your home extremely, rearing and leaping. Due to the fact that you understand that is what is going to occur when you position a unicorn horn on a 4 years of age. (Omygosh, she's practically 4!) I believe I actually accomplished all these requirements I set myself, and I am really pleased with how the entire thing came together, (therefore is she!).

When I made the horn, I was believing I would experiment a bit, start figuring things out. I didn't expect to be pleased with the very first thing I twiddled with, so I'm stuck with no pictures. I made a paper model in order to do this tutorial. Not the most beautiful images, but ideally they a minimum of make the procedure easy to see.

You will need:.

Craft Felt in Various Colours.
Packing.
Sewing Thread and Needle.
Additional Strong Quilting Thread.
Little Length of Elastic.
Headband.
Hot glue.
Scissors.
Plastic Gems.
Fabric Leaves (Or Make Felt Leaves).

I used sparkly white craft understandinged of her horn. Aside from the reality that it is, obviously, sparkly, the sparkle felt is a fair bit stiffer. Eliminate a slim triangle and fold it in half lengthwise, ideal sides together. Finish the open long side, marked with sharpy in the following pictures. Leave the bottom open. (That triangle was supposed to be fairly in proportion. The genuine thing was, I swear. Pretend that it is reasonably balanced, okay? Thanks.).

Trim off excess material, and turn right-side-out. Using extra strong quilting thread, cut a long piece, (enough to cover your spirals,) and knot off the end. Make it an excellent, huge knot, you don't desire it to pull through the felt when there is stress on it. Run the thread out near the idea of the horn from inside. (Not at the pointer.) Pull everything the way through, so that knot is the only part left within. Things the horn as firmly as you can, I utilized polyfill stuffing. If necessary, cut the bottom to even it out.

Start wrapping the thread down the horn in a spiral, securely enough to leave a great indent. This will give your horn a great spiraled shape, and keep the thread from sliding and slipping around on the horn. (This was the part I was most unsure about. I worried that the material would lot, or that the thread would not be strong enough to pull securely, or that it would not remain in location. None of those worries emerged, it worked extremely well.) Connect your thread off within, near the bottom of the horn. Position your horn on another piece of matching felt, trace the bottom circle, and cut it out.

Beginning with the within, wrap stitches around the edges of your felt, sewing the circle to the bottom of the horn, and tie it off. Attempt to hide your knot inside, or at least away from the edge.

I attached it to a good, broad, cloth-covered headband that we discovered at a dollar shop. To do so, determine a piece of flexible around the center of the headband to obtain your length, then make it a bit smaller sized so that it will extend comfortably into location. Sew the flexible ends together to form a loop. Stitch the flexible to the bottom of the horn. Take care to stitch the elastic all the way to the edges of the horn, or the base will bring up at the Learn More Here front and back. Make sure that the joint holding the elastic together gets stitched to the horn, this way it will end up on top of the headband, rather of as an uncomfortable swelling against your kid's head.

Your unicorn horn is total! Like magic, the paper horn all of a sudden transforms into a genuine one! Oh, wait ... * ehem * Anyhow, when on the headband, I included a little hot glue under the edges of the horn to assist keep it from wobbling any. I believe this would be fixed by using a larger flexible band than what I took place to have on hand.

Hot glue the material leaves down either side of the headband, overlapping a little and alternating instructions. Cut a variety of flowers from the coloured felt. (Tip: Your other half may get somewhat irritable if you attempt to do this in bed, stay with checking out a book.) I honestly believe layering has the biggest impact on how great they come out looking. I used hot glue to repair the layers together. I've no concept how well hot glue works on wool felt, but it works amazingly on eco felt. I think the heat actually fuses browse around this site the layers together to a level. For the large yellow flower, I merely cut a bunch of strips of felt, folded them in half, then added them entirely by their ends with a little thread.

Hot glue the flowers all over the headband, then hot glue the plastic gems to the. Make sure to overlap the base of the horn a bit and cover the rubber band. You are the proud brand-new owner of a unicorn horn flower crown!

I had a very difficult time keeping her still enough time to take any pictures ...

Her rainbow unicorn tail is now total, too, and I have a full blown unicorn galloping around the home all day. Discover that tutorial here. By the method, it would be really easy to stick a couple ears in there in the middle of the flowers. According to Kaia, nevertheless, she currently has two ears and didn't desire any more. (Don't take a look at me ... she wears lots of other animal ears, my reasoning does rarely have much result on her, however.).

Since you understand that is what is going to occur when you position a unicorn horn on a 4 year old. When I made the horn, I was thinking I would experiment a bit, begin figuring things out. Make sure that the joint holding the elastic together gets stitched to the horn, this method it will end up on top of the headband, instead of as an unpleasant swelling against your kid's head.

Make sure to overlap the base of the horn a bit and cover up the flexible band. You are the proud brand-new owner of a unicorn horn flower crown!

Leave a Reply

Your email address will not be published. Required fields are marked *